Controlled-products-systems-group 8550C-7 Manual do Utilizador Página 23
- Página / 82
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
23
Withouta properly installed safety reversal
system, persons (particularlysmall children)
could be SERIOUSLY INJURED or KILLED bya
closing garage door.
• Incorrectadjustmentof garage door travel
limits will interfere with proper operation of
safetyreversal system.
• After ANY adjustmentsare made, the safety
reversal systemMUST be tested. Door
MUST reverse on contact with 1-1/2" (3.8
cm) high object (or 2x4 laid flat) on floor.
To preventdamage to vehicles,be sure fully
open door provides adequate clearance.
INTRODUCTION
Your garage door opener is designed with
electronic controls to make setup and
adjustments easy.The adjustments allow you
to program where the door will stop in the
open (UP) and close (DOWN) position.The
electronic controls sense the amount offorce
required to open and close the door. The
force is adjusted automatically when you
program the travel.
NOTE: If anything interferes with the door’s
upward travel it will stop. If anything interferes
with the door’s downward travel, it will reverse.
To watch a short instructional video on
programming your newgarage door opener
use your smartphone to read the QR Code
below:
PROGRAMMING BUTTONS
The programming buttons are located on the
leftside panel ofthe garage door opener and
are used to program the travel.
UP (Open)
DOWN (Close)
UP Button
Adjustment
Button
DOWN Button
PROGRAMMING BUTTONS
Adjustments
- ELITE Series 1
- Garage Door Opener 1
- Preparation 2
- Carton Inventory 3
- Hardware 3
- Assembly 4
- 2 Tighten the Belt 5
- Installation 10
- 6 Install the light bulbs 11
- HARDWARE 13
- Install the Door Control 14
- Install the Protector System 17
- 1 Connect Power 21
- UP Button 23
- Adjustment 23
- DOWN Button 23
- PROGRAMMING BUTTONS 23
- Adjustments 24
- Battery 26
- Status LED 26
- Battery Backup* 27
- WARNING 28
- Features 29
- Door Control 30
- Navigation Buttons 31
- TO REMOTE 32
- Remote Control 33
- Maintenance 34
- To Open the Door Manually 34
- Troubleshooting 35
- Accessories 37
- Warranty 38
- Repair Parts 39
- Modéles 42
- Préparation 43
- Aperçu/Contenu de la boîte 44
- Matériel 44
- 1.3 Modèle 8550 : 45
- 2 Serrage de la courroie 46
- -fond de 49
- 5/16 po-9 x 1-5/8 po 49
- MATÉRIEL 50
- Axe de chape de 50
- 5/16 po x 50
- 2-3/4 po 50
- Anneau d’arrêt 50
- 6 Fixation des ampoules 52
- Vis autotaraudeuse 53
- 1/4 po-14 x 5/8 po 53
- Pose de la commande de porte 55
- Pose le Protector System 58
- OPTION A 59
- OPTION B INSTALLATION MURALE 59
- (non fournie) 59
- (non fournis) 59
- Alimentation 62
- Réglages 64
- Statut de 67
- Pile de Secours* 68
- 16. CONSERVEZ CES 69
- INSTRUCTIONS 69
- Fonctions 70
- Commande de Porte 71
- Télécommandes 73
- Entretien 75
- Dépannage 76
- Accessoires 78
- Garantie 79
- Pièces de rechange 80
Manuais e produtos relacionados com Sensores Controlled-products-systems-group 8550C-7
(2 páginas)
(8 páginas)AEG FÖKOXLIM0P manuály
Uživatelské manuály a uživatelské příručky pro ne AEG FÖKOXLIM0P.
Poskytujeme 2 manuály pdf AEG FÖKOXLIM0P ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais