Controlled-products-systems-group SLIDESMART DC 10F Manual do Utilizador Página 99
- Página / 148
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Connecting a Radio Receiver for Remote Open
Revision D Reference 6-1
Reference
Chapter 6
This section of the manual provides information which may be useful when installing SlideSmart operators.
It includes how to:
• Connect a Radio Receiver for Remote Open
• Install a Gate Locking Mechanism
• Install Vehicle Detectors and Loops
• Install Photoelectric Sensors
• Install Gate Edge Sensors
• Troubleshoot error codes, faults, and hardware issues
• Diagnose vehicle detector and loop faults
• Handle General Maintenance issues
C
ONNECTING
A
R
ADIO
R
ECEIVER
FOR
R
EMOTE
O
PEN
Take the following steps to mount a commercial
style 24VDC radio receiver (external antenna
type):
1. Install the receiver in the channel of the
chassis on either side of the control box.
2. Knock out the closest hole in the bottom of
the control box and route the wires to the
area marked RADIO OPTIONS. Only
three wire connections are needed because
the common wire and one radio output wire
are connected together. Figure 6-1 shows
additional wires from a two channel receiver.
3. Make sure to observe polarity and crimp
together the black radio common wire and
one of the radio output wires using a ¼-inch
spade connector.
4. Fasten the two crimped wires to the COM
terminal.
5. Connect the red wire to the +24V spade and connect the other radio output contact wire to the spade
marked OPEN.
Note:This terminal is the same as the input terminal labeled RADIO OPEN along the left edge of the Smart
DC Controller.
C
OM
EDGE
EYE
COM
+ 24 V
EMERG
OPEN
SHOW
LEDs
RA
D
I
O
OPTI
O
NS
E
D
G
E
+
24
V
O
P
E
N
C
O
M
D
U
A
L GA
T
E
B
A
U
S
E
R
2
C
OM
N
O
D
C
Two Channel Radio Receiver
Power
Shows connecons
for Remote Open
and Gate Edge (dashed line).
R2
R1
Figure 6-1.
- SlideSmart DC 1
- OMPONENTS 4
- Contents 5
- Introducing SlideSmart DC 9
- ECHNICAL 10
- NSTALLER 11
- Installer's Check List 12
- Safety Requirements 13
- ECONDARY 17
- NTRAPMENT 17
- ROTECTION 17
- Class I 18
- Class II 18
- Class III 18
- Class IV 18
- Class IV A B1, B2, C, D, or E 19
- MERGENCY 20
- & S 21
- NDUSTRIAL 22
- Installation 23
- Pad Condition 24
- Using an Existing Pad 25
- Front Installation 26
- Rear Installation 27
- NPACKING 28
- PUBLICPUBLIC 29
- SECURESECURE 29
- NSTALLATION 30
- Aligning the Chain 31
- Connect red battery wire 32
- Turn DC power ON 32
- WT 0 33
- GATE WEIGHT (LB) 33
- HYSECURITY 34
- GATE CLOSED 34
- Installing the Target Magnet 35
- Chapter 2 39
- Service Outlet 41
- 115VAC, 15A 41
- Wiring 115VAC Power 42
- Wiring 208/230VAC Power 42
- Voltage selector switch 43
- Map Legend 48
- MPORTANT 49
- ONSIDERATIONS 49
- PERATORS 49
- 50Ah batteries 51
- Accessory tray 51
- Post-mounted 51
- Display and Menu Options 53
- CT 0 (OFF) 55
- CLOSE TIMER 55
- Setting the Time and Date 61
- AP 0 (AC LOSS) 62
- UPS FAIL OPEN 62
- LD 5 63
- LCD CONTRAST 63
- User Menu 64
- DS 0 (OFF) 66
- DIAGNOSTIC LOGS 66
- Adjusting Gate Speed 69
- Adjusting the IES Sensitivity 70
- LL 0 (OFF) 71
- LEARN LIMIT 71
- Reinstating Factory Defaults 72
- Smart DC Controller 83
- Terminal 85
- Input Name Use 85
- HY-5A V 87
- (Bold - Default) 88
- Display Meaning 88
- Entrapment Sensor Connections 91
- Manual Push Button Station 92
- No. Name Description 93
- Bi-parting Gate Systems 95
- Slave Master 96
- Master Slave 96
- LL 0 (OFF) 97
- Master and Slave Menu Setup 98
- Reference 99
- USER 1 RELAY 101
- Installing a Lock for 102
- High Voltage 102
- Installer Menu 103
- NSTALLING 104
- ETECTORS 104
- Figure 6-7 106
- PERATION 107
- Other options include: 108
- UPERVISED 109
- ONNECTION 109
- Revision D Reference 6-13 111
- Two Channel Radio Receiver 113
- ONTROLLER 114
- ROUBLESHOOTING 114
- Display Description 115
- Possible Causes Solutions 115
- Alert or Error 121
- Installer 122
- Menu LCD Description 122
- Setting Options 122
- Bold = Factory Settings 122
- SlideSmart Schematics 123
- Figure 6-15 124
- AINTENANCE 125
- Electrical Controls 126
- Mechanical Maintenance 127
- Software Maintenance 127
- 1/16" to 1/8" 128
- EPLACEMENT 129
- General Maintenance 132
- Installation Configurations 133
- SLIDESMART INSTALLATION 134
- SPECIFICATION 134
- Parts & Limited Warranty 145
- G-2 Revision D 146
- April 2010, D0317 147
- PECIFICATIONS 148
Manuais e produtos relacionados com Segurança Controlled-products-systems-group SLIDESMART DC 10F
(36 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais