Controlled-products-systems-group 2000E Manual do Utilizador Página 6
- Página / 8
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Programming Keypad Parameters
(Default settings are in bold)
Command/Action Keys to Enter/Details
Change Keypad Parameters 32 # parameter # value # **
Parameter Value
0 – Duress Output Duration 1 – 255 Seconds (default = 5)
1 – Panic Output Duration* 1 – 255 Seconds (default = 5)
2 – Error Lockout Threshold 1 – 50 Attempts (default = 3)
3 – Error Lockout Duration 1 – 255 Seconds (default = 10)
4 – Auto-Entry Count 2 – 10 Digits (default = 4)
7 – Auto-Entry Keypress
Timeout
2 – 15 Seconds (default = 2)
10 – Wiegand Format 1 – 8 (default = 1, 26-Bit)
11 – Wiegand Pulse Width 1 – 255 (default = 8, 160µS)
12 – Wiegand Interpulse Spacing 1 – 255 (default = 32, 640µS)
Note: Refer to the Wiegand Format Chart below for parameter 8.
Change Wiegand Parameters 34 # parameter # value # **
Parameter Value
0 – Wiegand Site ID Refer to Wiegand Format Chart
1 – Wiegand Group ID Refer to Wiegand Format Chart
Note: The default setting for both settings is 0.
*Note: The Panic Output is activated by pressing the * and # keys
at the same time. This is used in case of emergency to activate an
auxiliary alarm device, such as a siren, that is used to indicate an
emergency condition only. This output should not be used to gain
access. All access control functionality should be programmed and
remain separate from the Panic Output functionality.
Resetting the Keypad
Note: This does not reset the keypad operating mode.
Command/Action Keys to Enter/Details
Reset Defaults Only 40 # 00000 # 00000 # **
Reset Entire Keypad 46 # 00000 # 00000 # **
Wiegand Format Chart
The keypad supports the following Wiegand formats (parameter
10).
Format
Value
Wiegand
Format
Largest
PIN Value
Largest
Site Value
Largest
Group
Value
1 26 bit 65535 255 N/A
2 28 bit 32767 255 N/A
3 29 bit 524287 255 N/A
4 30 bit 65535 255 15
5 31 bit 65535 255 31
6 32 bit 8191 2047 63
7 36 bit 999999 1023 N/A
8 29 bit 524287 255 N/A
Wiegand Data
When the keypad is configured in Wiegand mode, the keypad data
is sent as a complete Wiegand data packet, as though you
presented a card.
For example, when programming a user into an IEI Door Control
Module, you must program the user as though you were
programming a card. After entering the command to program a
card user, enter the code on the 2000e/eM keypad to send the data
to the controller.
Please refer to the Wiegand Interface Module instructions 6065700
Rev 1.0, the HubMax II Instructions 6065034 Rev 3.4 and the Hub
MiniMax II instructions 6055037 Rev 3.3 for complete details.
LED/Sounder Indications
Indicator Description
Steady Red* Door Locked
Steady Green* Door Unlocked (timed or latched)
Yellow Flashing Slowly Program Mode
Solid Yellow Program Error or Error Lockout
Alternating Red/Green Awaiting 2
nd
PIN of Two-Part User
LED's Cycling Left to Right Over Voltage Warning
LED's Cycling Right to Left Under Voltage Warning
3 Rapid Beeps Invalid Code
Pair of Double Beeps User Lockout Activated
Single Double Beep User Lockout Canceled
1 Long Beep, 1 Short Beep Access Denied, User Disabled
1 Long Beep, 3 Short Beeps Access Denied, User Lockout
1 Long Beep, 5 Short Beeps Access Denied, Code Mismatch
6 Quick Beeps Toggle Mode Activated
Sounder ¼ sec on, ¼ sec off Audio Alert 1
Beep Every 2 seconds Audio Alert 2
*Note: The Red/Green LED descriptions above are for Standalone
and Secured Series Mode only. The operation of these LED's in
Wiegand Mode is determined by the LED control wire (brown)
and how it is configured. The LED control is configured using
keypad options 19, 20, 21 and 22, which are programmed with
command 30.
Document #: 6104402, Rev 2.0 Page 6 of 8
Manuais e produtos relacionados com Painel de controlo Controlled-products-systems-group 2000E
(21 páginas)Philips KEY013 manuals
Owner’s manuals and user’s guides for MP3/MP4 players Philips KEY013.
We providing 1 pdf manuals Philips KEY013 for download free by document types: User Manual
Comentários a estes Manuais